Viper 160XV Instalační příručka

© 2005 Directed Electronics, Vista, CAN562V 07-05NOTE: This product is intended for installation by a professional installer only!Any attempt to inst

1100© 2005 Directed Electronics—all rights reservedwwiirriinngg ddiiaaggrraammssThe primary harness supplied with this unit is the standard 12-pin ha

© 2005 Directed Electronics—all rights reserved1111__________________________________________________________________________________________PPIINNKK/

1122© 2005 Directed Electronics—all rights reserved________________________________________________________________________NNoottee::Refer to TechTip

© 2005 Directed Electronics—all rights reserved1133pprriimmaarryy hhaarrnneessss ((HH11)) wwiirree ccoonnnneeccttiioonn gguuiiddeeWhen the system

1144© 2005 Directed Electronics—all rights reservedRemove any paint and connect this wire to bare metal, preferably with a factory bolt rather than yo

© 2005 Directed Electronics—all rights reserved1155This input comes from the factory set to 2 activation pulses. This means that it is necessary to ha

1166© 2005 Directed Electronics—all rights reserved((--)) LLiigghhtt FFllaasshh OOuuttppuuttNNOOTTEE::For parking light circuits that draw 10 amps

© 2005 Directed Electronics—all rights reserved1177Connect this wire to the accessory wire in the vehicle that powers the climate control system.Conne

1188© 2005 Directed Electronics—all rights reservedThis wire sends a negative pulse every time the remote start is activated or the doors are unlocked

© 2005 Directed Electronics—all rights reserved1199rreemmoottee ssttaarrtt hhaarrnneessss ((HH33)) wwiirree ccoonnnneeccttiioonn gguuiiddeeConne

22© 2005 Directed Electronics—all rights reservedttaabbllee ooff ccoonntteennttssBitwriter®, Code Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Swi

2200© 2005 Directed Electronics—all rights reservedThis wire MUST be connected to hood pinswitch. This input will disable or shut down the remote star

© 2005 Directed Electronics—all rights reserved22111. Make sure there is adequate clearance to the front and rear of the vehicle because it may move s

2222© 2005 Directed Electronics—all rights reservedDDiiaaggrraamm AA -- GGeenneerraall MMoottoorrss ttrruucckkss,, ssppoorrtt uuttiilliittyy v

© 2005 Directed Electronics—all rights reserved2233The Passlock I and Passlock II systems can be found in the following General Motors vehicles: ‘95

2244© 2005 Directed Electronics—all rights reservedbbyyppaassssiinngg GGMM vveehhiiccllee aannttii--tthheefftt ssyysstteemmss ((VVAATTSS))Vehicle

© 2005 Directed Electronics—all rights reserved2255pplluugg--iinn LLEEDD aanndd vvaalleett//pprrooggrraamm sswwiittcchhThese plug into the module.

2266© 2005 Directed Electronics—all rights reservedpprrooggrraammmmiinngg jjuummppeerrssThis jumper is used to determine the light flash output polar

© 2005 Directed Electronics—all rights reserved2277ttrraannssmmiitttteerr//rreecceeiivveerr lleeaarrnn rroouuttiinneeThe system comes with transmitt

2288© 2005 Directed Electronics—all rights reserved3.TTrraannssmmiitt.. While HHOOLLDDIINNGGthe Valet/Program switch, press the button on the transmi

© 2005 Directed Electronics—all rights reserved2299ttrraannssmmiitttteerr ccoonnffiigguurraattiioonnssThe transmitters can be programmed with the sep

© 2005 Directed Electronics—all rights reserved33wwaarrnniinngg!! ssaaffeettyy ffiirrssttThe following safety warnings must be observed at all times

3300© 2005 Directed Electronics—all rights reservedThe learn routine may be locked if previously programmed using the Bitwriter®. If the horn generate

© 2005 Directed Electronics—all rights reserved3311ffeeaattuurree mmeennuussFactory default settings are indicated in bboollddin the following featur

3322© 2005 Directed Electronics—all rights reservedffeeaattuurree ddeessccrriippttiioonnssThe features of the system are described below. Features th

© 2005 Directed Electronics—all rights reserved333311--22 CCHHIIRRPPSS OONN//OOFFFF::This feature controls the chirps that confirm arming and disarm

3344© 2005 Directed Electronics—all rights reserved11--1111 CCHHAANNNNEELL 22 LLIINNKKIINNGG ((NNOONNEE))//ARM, DISARM, BOTH::When programming to

© 2005 Directed Electronics—all rights reserved3355preset time that can be programmed in Feature 2-5. Once the starter has been engaged, the system wi

3366© 2005 Directed Electronics—all rights reservednecessary to program this feature off.22--1133 DDIIEESSEELL TTIIMMEERR——WWAAIITT--TTOO--SSTTAAR

© 2005 Directed Electronics—all rights reserved33772. Press and HHOOLLDDthe Valet/Program switch.3. Turn the ignition on and then off.4. Release the V

3388© 2005 Directed Electronics—all rights reservedrreeaarr ddeeffooggggeerr ccoonnttrroollThe rear defogger output can be remotely turned on/off an

© 2005 Directed Electronics—all rights reserved3399vvaalleett mmooddeeTo enter or exit Valet Mode with the Valet/Program switch:1. Turn the ignition

44© 2005 Directed Electronics—all rights reservediinnssttaallllaattiioonn ppooiinnttss ttoo rreemmeemmbbeerrIIMMPPOORRTTAANNTT!! This product is d

4400© 2005 Directed Electronics—all rights reservedf. Activate the remote start system. If the starter engages, immediately step on the brake to shut

© 2005 Directed Electronics—all rights reserved4411lite. Also make sure that the ground wire is going to a chassis ground and not to something under t

4422© 2005 Directed Electronics—all rights reservedwwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddeeBLACK ground inputVIOLET not usedBLUE (-) 2

© 2005 Directed Electronics—all rights reserved4433rreellaayy ssaatteelllliittee wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddeePINK (-) 20

© 2005 Directed Electronics—all rights reserved55 Some good control module locations are: Above the glove box, inside the center console, above the u

66© 2005 Directed Electronics—all rights reservedThings to remember when positioning the status LED: It should be visible from both sides and the rea

© 2005 Directed Electronics—all rights reserved77We recommend two possible sources for 12V constant: The (+) terminal of the battery, or the constant

88© 2005 Directed Electronics—all rights reservedcontrol the starter. Instead, the cold start circuit is used to prime the fuel injection system for s

© 2005 Directed Electronics—all rights reserved99To test for a tachometer wire, a multimeter capable of testing AC voltage must be used. The tachomete