Viper 5601 Instalační příručka

Security and Remote Start Model 5601Installation GuideThis product is intended for installation by a professional installer only! Attempts to install

10© 2008 Directed Electronics. All rights reserved.in the owners guide.Review and complete the Safety Check section of this guide prior to the svehic

11© 2008 Directed Electronics. All rights reserved.¢Primary harness (H1), 12-pin connectorH1/1RED/WHITE (-) 200mA TRUNK RELEASE OUTPUTH1/2RED (+)12v

12© 2008 Directed Electronics. All rights reserved.¢Heavy gauge remote start, (H3) 10-pin connectorH3/1PINK (+) IGNITION 1 INPUT/OUTPUTH3/2RED/WHITE

13© 2008 Directed Electronics. All rights reserved.wires directly to the vehicle you must place a 1-amp diode in line to prevent feedback from the veh

14© 2008 Directed Electronics. All rights reserved.Wire connection guides¢ Primary harness (H1)H1/1RED/WHITE (-) 200mA TRUNK RELEASE OUTPUTWhen the sy

15© 2008 Directed Electronics. All rights reserved.H1/4WHITE/BROWN LIGHT FLASH -ISOLATION WIRE - PIN 87a of onboard relayThis wire connects to pin 87

16© 2008 Directed Electronics. All rights reserved.H1/6VIOLET (+) DOOR TRIGGER INPUTThis wire is used in vehicles that have a positive (+) switched do

17© 2008 Directed Electronics. All rights reserved.directly to the dome light circuit, as the output cannot support the current draw of one or more li

18© 2008 Directed Electronics. All rights reserved.(+) Positive Light Flash Output(-) Negative Light Flash OutputWHITE H1/11(+) LIGHT FLASH OUTPUTWHIT

19© 2008 Directed Electronics. All rights reserved.Relay for Negative (-) Disarm Wire Relay for Positive (+) Disarm WireH2/2LIGHT GREEN/WHITE (-) 200m

Bitwriters with a date code of 6a or older require an IC upgrade (p/n 998M). Some bitwriters with a date code of 6B do not require the IC upgrade, ref

20© 2008 Directed Electronics. All rights reserved.H2/5WHITE/BLACK (-) 200mA AUX 3 OUTPUTThis wire provides 200 mA programmable output whenever the tr

21© 2008 Directed Electronics. All rights reserved.WAIT-TO-START bulb in the dashboard. In most diesels the wire is negative (ground turns on the bulb

22© 2008 Directed Electronics. All rights reserved.to be used like a siren output with arm/disarm honks. Refer to System Features Menu#1, Feature 10,

23© 2008 Directed Electronics. All rights reserved.H3/7PINK/WHITE (+) IGNITION 2 FLEX RELAY OUTPUTThis wire is factory programmed as Ignition 2 and ca

24© 2008 Directed Electronics. All rights reserved.2VIOLET/WHITE TACHOMETER INPUT WIREThis input provides the module with information about the engine

25© 2008 Directed Electronics. All rights reserved.¢ Remote start auxiliary output, 5-pinThese signals are provided to drive additional optional relay

26© 2008 Directed Electronics. All rights reserved.¢Door lock wire diagramsImportant: Depending on the vehicle, the door locks may be con-trolled by

27© 2008 Directed Electronics. All rights reserved.Neutral safety switch interfaceSome vehicles do not have an electrical neutral safety switch. Inste

28© 2008 Directed Electronics. All rights reserved.Plug-in LED and valet/program switchThe LED and valet switch are incorporated into the control cent

29© 2008 Directed Electronics. All rights reserved.Alarm trigger inputs shorter than 0.8 seconds trigger the WarnAway response, while inputs longer th

ContentsWarning! safety first...5What is included...

30© 2008 Directed Electronics. All rights reserved.¢ Tach learningTo learn the tach signal:1. Start the vehicle with the key.2. Within 5 seconds, pres

31© 2008 Directed Electronics. All rights reserved.D2D Jumper settingsThe security system has the ability to work with a compatible module through the

32© 2008 Directed Electronics. All rights reserved.Access door(Light Flash Fuse Jumper is under access door - use needle nose pliers tochange fuse pos

33© 2008 Directed Electronics. All rights reserved.Press and release the button any time during programming to go back to the main menu. Press and hol

34© 2008 Directed Electronics. All rights reserved.4. Open a door. (The GREEN wire, H1/8, or the VIOLET, H1/6 must be connected.5. Insert the key. Tur

35© 2008 Directed Electronics. All rights reserved.7. Transmit. While holding the Valet/Program switch, press the button on the remote control. Th

36© 2008 Directed Electronics. All rights reserved.1-Way remoteA U X Note: If Keypad Lock is On, press and then press to exit.The remote control butt

37© 2008 Directed Electronics. All rights reserved.Additional system featuresFor information about Valet mode, Remote starting the vehicle, Manual tra

38© 2008 Directed Electronics. All rights reserved.If the button is not released, the program jumps to the next menu and the siren chirps twice. There

39© 2008 Directed Electronics. All rights reserved.times to confirm access to the seventh feature.To select another menu:Press and hold the Valet/Progr

Menu 1 - Security...40Menu 2 - Convenience ...

40© 2008 Directed Electronics. All rights reserved.Feature menusNote: The default settings are indicated in bold type.¢ Menu 1 - SecurityMenuItemFeatu

41© 2008 Directed Electronics. All rights reserved.¢ Menu 2 - ConvenienceMenuItemFeature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+1 One-time BypassOne time b

42© 2008 Directed Electronics. All rights reserved.¢ Menu 3 - Remote startMenuItemFeature Opt. 1 Opt. 2 Opt. 3 Opt.4 Opt. 5+1 Transmission ModeManualA

43© 2008 Directed Electronics. All rights reserved.Feature descriptionsThe features of the system are described below. Features that have additional s

44© 2008 Directed Electronics. All rights reserved.chirps that confirm the arming and disarming of the system, Arm/Disarm chirps ON, w/Warn Away chirps

45© 2008 Directed Electronics. All rights reserved.1-9 Comfort Closure Off(1): The system can be programmed to close the win-dows when the system is l

46© 2008 Directed Electronics. All rights reserved.¢ Menu 2 - Convenience2-1 One time bypass Off: One time bypass ON. When programmed On (2) the unit

47© 2008 Directed Electronics. All rights reserved.optional dome light supervision feature must be installed as described in the Wire Connection Guide

48© 2008 Directed Electronics. All rights reserved.2-11 Aux 2 Validity (1) Latched (2), Latch reset w/ignition (3), 30-sec. Timed, (4) Output, (5) Off

49© 2008 Directed Electronics. All rights reserved.When set to voltage (2), the unit cranks the starter for the programmed time and then attempts to s

5© 2008 Directed Electronics. All rights reserved. Warning! safety firstThe following safety warnings must be observed at all times:Due to the complex

50© 2008 Directed Electronics. All rights reserved.input on the remote start unit. When the vehicle is running press the button the appropriate amount

51© 2008 Directed Electronics. All rights reserved.stays on for 10 minutes.Note: When the defogger mode is on, the output is always active and can be

52© 2008 Directed Electronics. All rights reserved.¢ Bitwriter®The Bitwriter® has the ability to fine tune certain features of the security system.

53© 2008 Directed Electronics. All rights reserved.Feature DefaultsettingOptional settingsSensor 1 level 7 (normal)0/1/2/3/4/5/6/7/8/9/10/11/12/13/14/

54© 2008 Directed Electronics. All rights reserved.Long term event historyThe system stores the last two full triggers in memory. These are not erasab

55© 2008 Directed Electronics. All rights reserved.Table of zonesWhen using the Diagnostic functions, use the Table of Zones to see which input has tr

56© 2008 Directed Electronics. All rights reserved.7 flashes Timer mode/Turbo mode/Manual mode error *8 flashes Neutral safety shutdown9 flashes

57© 2008 Directed Electronics. All rights reserved.Remote start safety checkBefore vehicle reassembly, the remote system must be checked to ensure saf

58© 2008 Directed Electronics. All rights reserved.Troubleshooting¢ Alarm Shock sensor doesn’t trigger the alarm:sHas the NPC® system been triggered?

59© 2008 Directed Electronics. All rights reserved.The Valet/Program switch doesn’t work.sIs it plugged into the correct socket? See Plug-In LED and

6© 2008 Directed Electronics. All rights reserved.tion immediately and consult with the user to fix the problem immediately.After the remote start modu

60© 2008 Directed Electronics. All rights reserved.or “scotch locks” are not recommended for any high current heavy gauge wiring.The vehicle starts, b

61© 2008 Directed Electronics. All rights reserved.Hood Open (gray wire).sFoot Brake active (brown wire).sNo Parking Brake input, Black/white neutra

N5102 2008-06Vista, CA 92081www.directed.com© 2008 Directed Electronics.—All rights reserved.

7© 2008 Directed Electronics. All rights reserved.What is included2 Remote Controls (p/n 7153V)sThe control module sControl center with integrated

8© 2008 Directed Electronics. All rights reserved.¢ D2DThe system has the ability to interface with an XK module through the D2D port. The advantage t

9© 2008 Directed Electronics. All rights reserved.¢ Status LEDThe status LED is built into the control center. An optional LED (p/n 8634) is available